Your over-the-range microwave is humming but the food stays cold, or it threw sparks and a puff of smoke. Call Acdc Appliance Repair and we connect you with a licensed, insured independent pro near Mobile who services OTR, built-in and drawer microwaves.
The cabinet hides a high-voltage capacitor that can store a deadly charge even when the unit is unplugged. That single part is the reason microwave repair should go to a trained pro, not to a weekend project.
We run a free referral line for homeowners. A dispatcher hears what the microwave is doing and connects you with an independent local technician who knows both the high-voltage side and the installation side of these units.
Each pro we connect you with runs an independent shop with the license and insurance local rules call for. Asking for proof on arrival is perfectly normal.
Some microwave parts cost more than people expect. You get a written, upfront quote from the technician before work begins, which lets you weigh it against buying new.
We look for a pro already working near Mobile. A same-day slot opens up regularly when local pros have breathing room, and the arrival window gets set while you are on the line.
The right pro arrives with an insulated capacitor discharge tool, a meter for testing the diode and transformer windings, the tech sheet for your model, and a survey meter to confirm no leakage once the repair is done.
These cover the over-the-range, built-in wall, drawer and convection combo models that are worth repairing. Each starts with a safe capacitor discharge before any testing.
Everything seems to run except the heating. That points to the high-voltage circuit: a failed magnetron, a shorted diode, an open capacitor, or a burnt transformer winding. The pro checks each part with a meter after bleeding the stored charge.
Blue flashes along the side wall usually come from a greasy or burnt waveguide cover, chipped cavity paint, or a damaged rack support on a convection model. Left alone, arcing can pit the cavity and ruin the magnetron.
Microwaves use a chain of door interlock switches plus a monitor switch. When a switch sticks, the monitor switch shorts the line on purpose and blows the line fuse, so the whole unit goes dark. A unit that runs with the door open needs to be unplugged right away.
Dead buttons, phantom beeps, or a unit that keeps running after the timer ends point to the membrane touchpad or a stuck relay on the control board. The technician reads the keypad circuit with a meter and checks the relays before ordering parts.
Because an OTR unit doubles as the hood over your cooktop, the vent side wears out too. The technician can replace a noisy fan motor, a burnt cooktop lamp, clogged grease filters, and the charcoal filter used on recirculating setups.
If the turntable sits still, the motor or the drive coupler is the likely culprit. An OTR microwave that tilts forward or shifts may have a loose mounting plate or top bolts that stripped the cabinet, and that needs attention before it drops onto the range.
Use this as a quick read before you call. Share what you see with the dispatcher, and the technician can bring the most likely parts.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Runs, light on, no heat | Magnetron, diode, capacitor or transformer failure | Each high-voltage part with the capacitor discharged |
| Completely dead, no display | Blown line fuse from a failed door switch | Fuse, interlock switches, monitor switch |
| Sparks or smoke inside | Burnt waveguide cover, chipped cavity paint | Cover, cavity surface, stirrer, rack supports |
| Keeps running at zero or with door open | Welded relay or failed interlock | Control board relays and door switch chain |
| Plate will not turn | Turntable motor or coupler | Motor continuity, coupler, roller ring |
| Vent fan loud or dead | Fan motor bearings, greasy filters | Fan motor, damper, grease and charcoal filters |
A basic countertop microwave usually is not worth a service call, and most technicians will tell you so on the phone. Over-the-range units, built-in wall models, drawer microwaves and convection combos are a different story. They cost more, they fit a cutout or bracket, and swapping one means trim kits, cabinet work and a vent connection.
Unplug it, leave the cover on, and call. A dispatcher answers day and night.
Tell the dispatcher what type of microwave you have, whether it sits over the range, in a wall, or in a drawer, and what it is doing. If you can, read off the model number from the tag inside the door frame.
An independent technician working close to Mobile gets the job, and the dispatcher shares the arrival window. Same-day arrivals are routine when a local independent pro is free.
The technician unplugs the unit, discharges the capacitor with an insulated tool, and tests the high-voltage parts, door switches and control board. OTR models may need to come off the wall plate for access. You get a written, upfront quote before work starts.
After the repair, the pro heats a cup of water to confirm output and, after any high-voltage work, sweeps the door seal with a microwave survey meter to check for leakage. Written coverage for parts and labor is the norm among the pros we connect; ask for it.
Our over-the-range microwave went completely dark mid-popcorn. The technician found a blown line fuse, then traced it to a cracked door switch. He replaced both and showed me why the fuse would have blown again if he had only swapped the fuse.
The built-in in our wall oven stack hummed but did not heat. A new one would have meant a new trim kit too. The tech tested the diode and magnetron, replaced the magnetron, and checked for leakage with a meter before he left.
Blue sparks kept flashing inside the cavity. The technician pulled a waveguide cover that was charred from spatter, put in a new one, and told me how to wipe it down so it does not happen again.
Our microwave drawer would not stop running after the timer hit zero. The pro found a welded relay on the control board, ordered the board by model number, and came back two days later to install it.
When the light, fan and turntable all work but food stays cold, the high-voltage circuit has failed. The most common causes are a bad magnetron, a shorted diode, an open capacitor, or a burnt transformer. These parts carry lethal voltage, so let a trained technician test them.
Not until someone looks at it. Arcing tends to start at a greasy waveguide cover or a bare spot in the cavity paint, and it can take out the magnetron if it keeps happening. If it smokes, leave the door shut and unplug it if the cord is within safe reach.
A totally dark microwave often has a blown line fuse. The fuse usually blows because a door interlock switch failed and the monitor switch shorted the circuit on purpose. Replacing only the fuse is not enough; the technician tests the whole switch chain.
Frequently. Over-the-range and built-in units are expensive and fitted to the opening, so a new one brings its own installation costs. Small countertop models are usually better replaced. With a written quote from the pro in hand, you can make the call.
Please do not. The high-voltage capacitor can hold a lethal charge long after the unit is unplugged, and a slip with a screwdriver can be fatal. Leave the cabinet closed and let a trained pro use an insulated discharge tool.
You should request it after any magnetron, door or high-voltage repair. Many technicians run a survey meter around the door edges and vents as a final check that nothing is leaking.
We route microwave calls from houses, condos and apartments throughout Mobile and nearby neighborhoods. Dispatchers send each job to an independent pro already working close to your address, which helps when an OTR unit needs a second set of hands to lift off the wall plate.
Someone answers around the clock. Calls after hours are typically scheduled for the first slot next morning, while daytime calls can become same-day visits when a nearby pro has room.
